Store
Showing 73–78 of 82 results
-
Quick viewVRAD10- Cerwin Vega -10″ Vega Powered Active Subwoofer w/ Passive...
$249.00Add to cartSpecifications
- Slim 10” 2Ω Subwoofer
- Built-In Passive Radiator for extended bass response
- Power: 200W RMS @ 2Ω @100Hz, 450W MAX
- Bass Boost: 0-12dB
- Subsonic Filter: 35Hz
- LPF Filter: 75-150Hz
- PWM MOSFET Power Supply/Thermal Protection Circuit
- Adjustable Input Sensitivity
- Remote Subwoofer Control Included
- RCA and High-Level Inputs
- Delayed Soft Remote Turn On
- Dimensions: 13.6” X 9.65” X 2.4”(L X W X H) 345 X 245 X 65 mm (L X W X H)
- Remote Bass Knob Included
-
Quick viewWAVTECH bassRESTOR Bass Restoration Processor
$195.00Add to cartThere are certain types of music that just don’t have enough good, low bass. If you listen to classic rock, older hip-hop or Banda music, you know that something is missing. The bassRESTOR fills in the gaps and adds just the right amount of bass back into your music. A unique Multi-Function Remote Level Control (RLC) lets you adjust the overall bass volume, the amount of bass restoration effect needed for a particular song or defeat the effect completely when no restoration is required.
The bassRESTOR has both speaker level and RCA inputs, so it integrates easily with factory or aftermarket sources. There is a variable frequency subsonic filter for fine system tuning.
-
Quick viewWAVTECH IRAD Ignition/ Remote Generator + Delay
$40.00The technology in the Patented IRAD make it the ultimate installation tool. It provides solutions to 3 very specific problems faced in today’s installations. This easy to program device allows you to add a switched 12-volt output, a remote output with adjustable delay and a relay/solenoid control to overcome the issues created by vehicles with start/stop systems.Add to cart -
Quick viewWAVTECH link2 2-Channel LOC
$65.00Add to cartIf you need a high-quality 2-channel LOC, but don’t require additional features like summing or auxiliary inputs, the link2 is the perfect solution. It is extremely small so it will fit almost anywhere, simplifying installations.
It has OEM load detect for factory systems that require resistance to function properly. The link2 will accept up to 40V RMS through its speaker inputs, while delivering up to 10V RMS of output at less than 50 ohms.
-
Quick viewWAVTECH link4 4-Channel LOC w/Summing and Remote
$149.00Add to cartWhen it comes to adding an amplifier or amplifiers to your factory audio system, the link4 does what models from competing brands just can’t. Simply put, it is the most flexible 4-channel LOC available today.
The link4 can directly accept 4-channels of input and give you 4-channels of output. It can accept 2-channels of input and give you 4-channels of output. If you input 4-channels, you can sum them down to 2-channels of output and pass through another 2-channels for retained sub level control. It even has a 3.5mm Auxiliary Input so you can add your phone or other portable device to the system. No other 4-channel LOC can do all of that.
As an added bonus, it includes a "Patent Pending" Multi-Function Remote Level/Source Control that can adjust your subwoofer output level, the volume of the auxiliary source or serve as a Master Volume Control for your entire system. This is especially useful in OEM systems where speed sensitive volume dependent equalization is present.
-
Quick viewWAVTECH link6 6-Channel LOC w/Summing and Remote
$195.00Add to cartWhen upgrading your audio system in a typical front, rear and subwoofer set-up, the link6 is the perfect tool for the job. Getting its input from your factory stereo’s front and rear speaker leads, it can provide front, rear and subwoofer outputs for your aftermarket amplifier or amplifiers.
Some factory audio systems require summing when adding aftermarket amplifiers, because no full range signal is present. When this is necessary, the link6 combines the sum of the frequencies present, providing the full range signal your amplifiers need.
For added flexibility, the link6's multi-function remote provides four unique configurations, based on the specific application requirements of your system. It can work as a subwoofer level control for fine tuning the amount of bass in your system, or as a master volume control in more complex installations.